Featured models

Browse by date
β J F M A M J J A S O N D
1999                        
2000                        
2001                        
2002                        
2003                        
2004                        
2005                        
2006                        
2007                        
2008                        
2009                        
2010                        
2011                        
2012                        
2013                        
2014                        
2015                        
2016                        
2017      

Chat Page News
Friday 28th April 2017

Please bookmark http://chat.palsite.com/chat_page.py as the new URL.

previous new post   refresh  next
Roderick
Sunday 26th March 2017
9:51 pm U.K.

[email protected]

Don Sugden,

Ideally you should get a Sony AV-340CE powersupply, make sure you get one with a XLR rather than a DIN plug.

Or if you want to use the Ebay cable, you will need a 12V 2.6A DC supply.

nickmugford
Sunday 5th March 2017
2:36 am U.K.

[email protected]

remove pinch roller,sandpaper the shine off,wash with methylated spirts and replace,see what happens,check tape for tightness also,rewind/fast forward couple of times.

nickmugford
Wednesday 1st March 2017
12:36 am U.K.

[email protected]

Have three working models plus one for parts for disposal,at present converted to s-video but easily reverted to composite although s-video is better quality.

david [email protected]
Wednesday 8th February 2017
3:50 am U.K.

[email protected]

U-Matic VO-2860 P On play mode it starts, a few seconds after the pinch roller makes contact it cuts off Please Help

Craig
Tuesday 31st January 2017
5:58 pm U.K.

[email protected]

Does anyone have any EPK's from older movies? Back in the 80's, I believe they were all on U-Matic. Was looking to see if anyone had any leads on them.

Juha Jauhiainen
Saturday 5th November 2016
7:19 pm U.K.

[email protected]

http://www.digiommel.fi/Improved%20Image%20Quality%20of%20Old%20U-matic%20Recordings.pdf

Here is perhaps the best Low Band player in the world (PAL). Also with a Y / C output of course. If and when the others do not get played back your tapes, we can. Comments are welcome.

Roderick
Friday 4th November 2016
9:42 pm U.K.

[email protected]

Michael,

First step would be to thoroughly clean the threading path.

Most likely problem is a build-up of dirt that stops the threading ring from completing its' cycle.

If it doesn't activate the switch at the end, the machine goes in 'tape protection' mode and takes tension off the tape.

Have a try and let us know if you had any success.

Mr. Michael Heap
Friday 4th November 2016
7:56 pm U.K.

[email protected]

The Sony VO-5850P has developed a tape transport fault so that when inserting a cassette into the recorder the tape is at first stretched out round the record head in the normal way. The tape then almost immediately goes slack. The recorder does not go into the standby mode. Play, record, search, fast forward, fast rewind do not work. The cassette cannot be ejected.

I am advised by a video repair engineer that this is due to the failure of a component on the circuit board that controls the tape transport and that as it is impossible to identify the component that has failed the best remedy is to replace the entire circuit board. However the Sony VO-5800 /5850 series are obsolete in the UK and circuit board spares are difficult to find. Advice welcome.

Karl Webb
Saturday 15th October 2016
3:31 pm U.K.

[email protected]

Hi folks,

I have just powered up my Sony VP 5030 player after it not. Ring used for a while. The machine then made a tripping noise and loads of Smoke came out of it, its smells terrible. I have taken it outside and left it while I try and figure out what happened. I think it must of finally gave up the ghost

Ron
Monday 10th October 2016
10:54 pm U.K.

[email protected]

Hi,

I have recently purchased a VO-9800P and it seems the machine is stuck in SP/High Band mode. When I place a Low band tape into the machine it loads fine and plays but the SP/High light remains on and there is no video signal.

I have read that there is a pin that falls into a slot on SP tapes that identify the tape type. Could this pin switch be faulty? Is it an easy fix?

Or is there a manual override to switch the machine between High and Low band?

Any advice would be much appreciated.

Thank you

Ron

previous new post   refresh  next